Plumbing Essentials: A Prerequisite for Installing a Bathtub
Plumbing Essentials: A Prerequisite for Installing a Bathtub
Blog Article
How do you really feel with regards to Installing A Bathtub?
Installing a bathtub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately difficult job. If the old tub is easily available, the task can move quickly; if you have to open a wall surface to eliminate the old tub and also position the brand-new bath tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will require an assistant to leave the old bathtub and set in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. As opposed to hiring a service provider to take control of a halfway-completed task, it is better to take into consideration using one before you begin. Chances are you might need a specialist plumber to make tube connections.
This short article will help you install a new bath tub in your bathroom if you have actually already acquired a new tub and do not need to change the setup of your previous water pipelines.
Your tools and also material list should consist of the following:
Preparing for the Setup
To start with, the supporting structure provided with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will come from the pipes. Once the supply pipes have been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. When the taps have actually been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are handy in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little points.
The next objective is to make certain that the tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the tub up until the spirit level reviews degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the other tap.
Turn on the water system and also check all joints and brand-new pipework for leakages and also tighten them if required. Fill the bath tub and additionally examine the overflow outlet and also the regular outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bath tub needs to wait until the bath tub has actually been utilized at least once as this will settle it into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washers are in location in between the tap and also the sink. Safeguard the tap in position with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind needs to be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to break a stiff seal, causing the water to permeate the wall surface in between the bath and also the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are sold in tubes as well as cartridges, and can securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to permit the movement experienced when the tub remains in usage. The sealant can break rather early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the market. It is recommended to fit the tiles utilizing waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic person who reads about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was sensible. Are you aware of somebody who is fascinated with How to Install a Bathtub? Do not hesitate to share it. Many thanks for your time. Please check our blog back soon.
Quality assurance? Connect. Report this page